Prosthetic Biomechanics In Engineering

Download or read book Prosthetic Biomechanics in Engineering written by N.A. Abu Osman and published by CRC Press. This book was released on 2021-12-30 with total page 273 pages. Available in PDF, EPUB and Kindle. Book excerpt: Prosthetic biomechanics is an interdisciplinary field of engineering, medicine, and biology, focused on enhancing people’s lifestyles. In the past 20 years, the field of prosthetic biomechanics and its potential have grown due to the support of advances in engineering technologies. Prosthetic Biomechanics in Engineering is about the recent advances in prosthetic engineering research. The scope of the book is focused on the design, development, and evaluation of a prosthetic systems that are being used in biomechanical applications. The book covers advanced materials, conceptual design, classification, ergonomics design applications, brain computer interface (BCI) system, motion analysis, postural stand stability, upper and lower limb prosthetics, types of suspension systems for prosthetics, Fiber Bragg Grating-based techniques, and pressure on the residual limb and the socket. The early chapters effectively describe new sensors for in-socket systems, new pylon material, and advanced gait analysis. Further chapters discuss advanced techniques for the design and development of prosthetics based on clinical and emergency uses. The information provided in this book is intended for researchers and investigators to encourage further advances in the field of prosthetics research, and for the development of rehabilitation equipment for the improvement of human health, and it: Presents recent advances in prosthetic biomechanics engineering research Discusses the design and development of limb prosthetic systems Explores advanced concepts of the prosthetic sockets Describes gait analysis of prosthetics and orthotics Dr Noor Azuan Abu Osman is a practicing engineer and Professor of Biomechanics with Department of Biomedical Engineering, Faculty of Engineering, University of Malaya, Malaysia.

Download or read book Biomechanics of Lower Limb Prosthetics written by Mark R. Pitkin and published by Springer. This book was released on 2009-10-14 with total page 153 pages. Available in PDF, EPUB and Kindle. Book excerpt: Foreword from a Clinical Biomechanist, Applied Physiologist and Prosthetist teaching graduate students in Prosthetics & Orthotics. While there are many books on Biomechanics, arguably the quintessential science of limb prosthetics, none addresses the fundamental principles in sufficient detail and depth to be practically useful to the prosthetist, rehabilitation specialist or researcher. Dr. Pitkin’s monograph is an exemplary collection of theoretical principles from his research and o- ers, presented in its clinical and applied biomechanics form. The textbook provides an excellent overview of the many facets of lower limb prosthetic design and engineering for the ardent clinician researcher and student. The book delves into many of the basic concepts that are required knowledge for the clinician and the scientist to have as the foundation for their work. Dr. Pitkin has an e- quent manner in which he reflects on the history and literature to tell the storied evolution of prosthetic design . He takes the reader on a journey to consider his theories, which have substantive foundations to contemplate. By the end of chapter one, we have the basic h- tory and an appreciation for the rationale behind the “rolling joint ankle” with evidence to support his theoretical views.

Download or read book Prosthetic Biomechanics in Engineering written by N.A. Abu Osman and published by CRC Press. This book was released on 2021-12-30 with total page 257 pages. Available in PDF, EPUB and Kindle. Book excerpt: Prosthetic biomechanics is an interdisciplinary field of engineering, medicine, and biology, focused on enhancing people’s lifestyles. In the past 20 years, the field of prosthetic biomechanics and its potential have grown due to the support of advances in engineering technologies. Prosthetic Biomechanics in Engineering is about the recent advances in prosthetic engineering research. The scope of the book is focused on the design, development, and evaluation of a prosthetic systems that are being used in biomechanical applications. The book covers advanced materials, conceptual design, classification, ergonomics design applications, brain computer interface (BCI) system, motion analysis, postural stand stability, upper and lower limb prosthetics, types of suspension systems for prosthetics, Fiber Bragg Grating-based techniques, and pressure on the residual limb and the socket. The early chapters effectively describe new sensors for in-socket systems, new pylon material, and advanced gait analysis. Further chapters discuss advanced techniques for the design and development of prosthetics based on clinical and emergency uses. The information provided in this book is intended for researchers and investigators to encourage further advances in the field of prosthetics research, and for the development of rehabilitation equipment for the improvement of human health, and it: Presents recent advances in prosthetic biomechanics engineering research Discusses the design and development of limb prosthetic systems Explores advanced concepts of the prosthetic sockets Describes gait analysis of prosthetics and orthotics Dr Noor Azuan Abu Osman is a practicing engineer and Professor of Biomechanics with Department of Biomedical Engineering, Faculty of Engineering, University of Malaya, Malaysia.

Download or read book Prosthetic Designs for Restoring Human Limb Function written by William Craelius and published by Springer Nature. This book was released on 2021-07-30 with total page 231 pages. Available in PDF, EPUB and Kindle. Book excerpt: This textbook provides a thorough introduction and overview of the design and engineering of state-of-the-art prosthetics and assistive technologies. Innovations in prosthetics are increasingly made by cross-disciplinary thinking, and the author introduces the application of biomedical, mechanical, electrical, computer, and materials engineering principles to the design of artificial limbs. Coverage includes the fundamentals of biomechanics, biomechanical modeling and measurements, the basics of anatomy and physiology of limb defects, and the historical development of prosthetic design. This book stimulates the innovative thinking necessary for advancing limb restoration, and will be essential reading for students, as well as researchers, professional engineers, and prosthetists involved in the design and manufacture of artificial limbs. Learning enhanced by the exercises, including physical modeling with MATLAB and Simulink; Includes appendices with relevant equations and parameters for reference; Introduction to the design and engineering of prosthetics and assistive technologies.

Download or read book Design Tools and Methods in Industrial Engineering written by Caterina Rizzi and published by Springer Nature. This book was released on 2019-09-19 with total page 989 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book reports on cutting-edge design methods and tools in industrial engineering, advanced findings in mechanics and material science, and relevant technological applications. Topics span from geometric modelling tools to applications of virtual/augmented reality, from interactive design to ergonomics, human factors research and reverse engineering. Further topics include integrated design and optimization methods, as well as experimental validation techniques for product, processes and systems development, such as additive manufacturing technologies. This book is based on the International Conference on Design Tools and Methods in Industrial Engineering, ADM 2019, held on September 9–10, 2019, in Modena, Italy, and organized by the Italian Association of Design Methods and Tools for Industrial Engineering, and the Department of Engineering “Enzo Ferrari” of the University of Modena and Reggio Emilia, Italy. It provides academics and professionals with a timely overview and extensive information on trends and technologies in industrial design and manufacturing.

Download or read book Lower-Limb Prosthetics and Orthotics written by Joan Edelstein and published by CRC Press. This book was released on 2024-06-01 with total page 391 pages. Available in PDF, EPUB and Kindle. Book excerpt: Lower-Limb Prosthetics and Orthotics: Clinical Conceptsis a comprehensive overview of lower-limb prosthetics and orthotics, covering normal and pathological gait, lower-limb biomechanics, clinical applications, as well as prosthetic and orthotic designs and components. Joan Edelstein and Alex Moroz have writtenLower-Limb Prosthetics and Orthotics with the clinician’s perspective in mind. Clinical management is incorporated throughout the text, including basic surgical concepts, postoperative management, preprosthetic care, and training in the use of devices. Additionally, this text incorporates unique features relevant to physicians such as prescription writing and prosthetic and orthotic construction and modification, as well as, the latest research regarding energy consumption and long-term utilization of prostheses. Chapters Include: Orthotics in neuromuscular diseases Orthotics in pediatrics Functional expectations Gait and activities training Transtibial and transfemoral prostheses and components Transtibial and transfemoral biomechanics, evaluation, and gait analysis Disarticulations and Bilateral Amputations With over 150 line drawings and photographs to supplement the text, Lower-Limb Prosthetics and Orthotics: Clinical Concepts is ideal for clinicians in the fields of physical medicine and rehabilitation, orthopedics, vascular surgery, physical therapy and occupational therapy.

Download or read book The Promise of Assistive Technology to Enhance Activity and Work Participation written by National Academies of Sciences, Engineering, and Medicine and published by National Academies Press. This book was released on 2017-09-01 with total page 503 pages. Available in PDF, EPUB and Kindle. Book excerpt: The U.S. Census Bureau has reported that 56.7 million Americans had some type of disability in 2010, which represents 18.7 percent of the civilian noninstitutionalized population included in the 2010 Survey of Income and Program Participation. The U.S. Social Security Administration (SSA) provides disability benefits through the Social Security Disability Insurance (SSDI) program and the Supplemental Security Income (SSI) program. As of December 2015, approximately 11 million individuals were SSDI beneficiaries, and about 8 million were SSI beneficiaries. SSA currently considers assistive devices in the nonmedical and medical areas of its program guidelines. During determinations of substantial gainful activity and income eligibility for SSI benefits, the reasonable cost of items, devices, or services applicants need to enable them to work with their impairment is subtracted from eligible earnings, even if those items or services are used for activities of daily living in addition to work. In addition, SSA considers assistive devices in its medical disability determination process and assessment of work capacity. The Promise of Assistive Technology to Enhance Activity and Work Participation provides an analysis of selected assistive products and technologies, including wheeled and seated mobility devices, upper-extremity prostheses, and products and technologies selected by the committee that pertain to hearing and to communication and speech in adults.